ELASTOPHENE FLAM 25 PDF

ELASTOPHENE® FLAM 25 AR T3 is a SBS elastomeric bitumen waterproofing membrane with a glass grid / glass fleece reinforcement. The topside is protected . ELASTOPHENE® 25 AR must be applied by torch-on techniques on a weldable underlayer (FLAM) or bonded with bitumen (EAC free of oxidized bitumen) on a. ELASTOPHENE® FLAM is a flexible SBS elastomeric bitumen waterproofing membrane with a non-woven polyester reinforcement. Both sides are.

Author: Samura Tetaur
Country: Hungary
Language: English (Spanish)
Genre: Love
Published (Last): 26 May 2006
Pages: 234
PDF File Size: 19.67 Mb
ePub File Size: 17.3 Mb
ISBN: 143-9-58394-310-3
Downloads: 51119
Price: Free* [*Free Regsitration Required]
Uploader: Dilrajas

The photos on this page describe the work. Because there are few right angles, there are lots of triangles to be filled in.

ELASTOPHENE® FLAM 25 – Soprema

The weekend brings heavy rain to test the waterproofing — not a drop gets through to the house. Chauffage du sur-renfort et de la platine. For example the first layer could be omitted, and the insulation glued directly to elastopheen existing surface. Before work begins, the existing concrete elastopuene was elastophsne with a high pressure bar hose equipped with a rotating jet.

Before the insulation is laid, the channels carrying the rain water are reinforced: Click on figure to enlarge. If there is a risk of rain, then the Knauf Thane ET glued to the first layer must be entirely enclosed by the second layer, even if this means performing work not needed by the final waterproofing. Cinq points de Sopracolle par plaque. The time has come to re-do the waterproofing on the terrace roof of my house.

L’isolation Knauf Thane ET. The third bitumous layer is a reinforced bitumen with its lower face covered by a film which melts when heated, gluing it to the second layer. Creative Commons Attribution – NoDerivs 3. This second layer of bitumen should be placed on the Knauf Thane ET within a few hours to ensure that the Sopracolle glue speads out under the pressure of the layer of bitumen above. Il est bien plus rapide de remplacer les renforts par le flashing: The collector is trimmed before applying the outer reinforcement.

  EVANGELINE ANDERSON PURSUED PDF

On my roof, the rolls of the final layer are positioned north-south, so the second layer must be east-west. Rodolphe Ferracane, e-mail contact AFR-etancheite.

ELASTOPHENE® FLAM 25 AR

Cutting nord end of a roll of finishing layer. Reinforcement at junction of standups.

The second bitumous layer is of the same material as the first. Good waterproofing requires a reinforcing piece between the roof and the wall.

Since the new waterproofing and the insulation will raise the roof, the rainwater drains must also be raised. Finishing around rain water collector See 2. Cliquer sur les photos pour les agrandir.

ELASTOPHENE® 25 AR

Removal of remnants of previous waterproofing. The figure shows the three layers and the sidewall reinforcement for each layer. The work specified by this standard is often referred to as Three layers plus insulation, with heated reinforcement. The two layers should be perpendicular to one another. When reading estimates for waterproofing on flat roofs you may find that the estimate is lightened to reduce the price.

ELASTOPHENE® 25 – Soprema

The top serface is covered with flakes of stone which protect it against the ultra-violet. The joint of the flat roof and the rising walls that surround the roof are a possible source of leaks. Welding the outer reinforcement onto the collector.

  ERIN NIHONGO DEKIMASU PDF

As with the 1st layer, the joint of the flat roof and the rising walls that surround the roof are a possible source of leaks. Soudage du renfort sur platine et dalle. The first layer and the sidewall reinforcement are complete after 4 days. Applying the insulation requires careful attention to the weather forecast and the planning of the work. The rain water collector is positioned through a hole cut in the sidewall reinforcement, and then heated to glue it to the sidewall.

The orientation of the second layer depends on the way in which the third layer will be applied. Click on photo elastkphene enlarge. The Elastophene 25 is rolled out and cut to fit.

The first layer, which provides the waterproofing, is of elastic bitumen, 2. Pas une goute n’entre dans la maison. Click on the photos to enlarge them.

Last drops of the weekend’s heavy rain. Heating the outer-reinforcement and the ekastophene. Creative Commons Attribution – Pas de Modification 3. These are ajusted now but will be fitted later taking into account the future height of the finished surface. Fitting the 2nd layer in front of the future rain collector. It prevents water vapour reaching the insulation, and serves as a base for the finishing layer.

The rain water collector will pass through this. Finition autour de la platine. La partie bitume fait approximativement 2. Bitumous glue is applied to the rising side walls.